View M48T36_1269668.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M48T36
CMOS 32K x 8 TIMEKEEPER SRAM
PRODUCT PREVIEW
INTEGRATED ULTRA LOW POWER SRAM, REAL TIME CLOCK, POWER-FAIL CONTROL CIRCUIT and BATTERY FREQUENCY TEST OUTPUT for REAL TIME CLOCK AUTOMATICPOWER-FAIL CHIP DESELECTand WRITE PROTECTION WRITE PROTECT VOLTAGE: - M48T36Y: 4.2V VPFD 4.5V SMALL OUTLINE PACKAGE PROVIDES DIRECT CONNECTION for a SNAPHAT HOUSING CONTAINING the BATTERY and CRYSTAL SNAPHAT HOUSING (BATTERY and CRYSTAL) REPLACEABLE MICROPROCESSOR POWER-ON RESET PROGRAMMABLE ALARM OUTPUT ACTIVE in the BATTERY BACK-UP MODE BATTERY LOW WARNING
44 1
SOH44 (MH) Battery SNAPHAT
Figure 1. Logic Diagram
VCC
VCCQ
15 A0-A14
8 DQ0-DQ7
Table 1. Signal Names
A0-A14 DQ0-DQ7 IRQ/FT RST WDI E G W VCC VCCQ VSS VSSQ July 1995 Address Inputs Data Inputs / Outputs Interrupt / Frequency Test Output (Open Drain) Power Fail Reset Output (Open Drain) Watchdog Interrupt Chip Enable Output Enable Write Enable Supply Voltage Supply Voltage (DQ) Ground Ground (DQ)
WDI W E G M48T36 IRQ/FT RST
VSS
VSSQ
AI01624
1/17
This is preliminary information on a new product now in development. Details are subject to change witho ut notice.
M48T36
Table 2. Absolute Maximum Ratings
Symbol TA TSTG VIO VCC IO PD Parameter Ambient Operating Temperature Storage Temperature (VCC Off, Oscillator Off) Input or Output Voltages Supply Voltage Output Current Power Dissipation Value 0 to 70 -40 to 85 -0.3 to 7 -0.3 to 7 20 1 Unit C C V V mA W
Note: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to the absolute maximum ratings conditions for extended periods of time may affect reliability. CAUTION: Negative undershoots below -0.3 volts are not allowed on any pin while in the Battery Back-up mode.
Figure 2A. DIP Pin Connections
A14 A12 A7 A6 NC NC A5 A4 A3 IRQ/FT RST WDI A2 A1 A0 NC NC DQ0 DQ1 DQ2 VSSQ VSS 1 44 2 43 3 42 4 41 5 40 6 39 7 38 8 37 9 36 10 35 11 34 M48T36 12 33 13 32 14 31 15 30 16 29 17 28 18 27 19 26 20 25 21 24 22 23
AI01625
VCC VCCQ W A13 A8 NC NC A9 A11 G NC NC A10 E DQ7 NC NC NC DQ6 DQ5 DQ4 DQ3
Warning: NC = Not Connected
DESCRIPTION The M48T36 TIMEKEEPERTM RAM is a 32K x 8 non-volatile static RAM and real time clock. The monolithic chip is available in a special package to
provide a highly integrated battery backed-up memory and real time clock solution. The M48T36 is a non-volatile pin and function equivalent to any JEDEC standard 32K x 8 SRAM. It also easily fits into many ROM, EPROM, and EEPROM sockets, providing the non-volatility of PROMs without any requirement for special write timing or limitations on the number of writes that can be performed. The 44 pin 330mil SO provides sockets with gold plated contacts at both ends for direct connection to a separate SNAPHATTM housing containing the battery and crystal. The unique design allows the SNAPHAT battery package to be mounted on top of the SO package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surface-mounting.The SNAPHAT housing is keyed to prevent reverse insertion. The SO and battery packages are shipped separately in plastic anti-static tubes. The SO package is also available to ship in Tape & Reel form. For the 44 lead SO, the battery package (i.e. SNAPHAT) part number is "M4T44-BR12SH1". As Figure 3 shows, the static memory array and the quartz controlled clock oscillator of the M48T36 are integrated on one silicon chip. The two circuits are interconnectedat the upper eight memory locations to provide user accessible BYTEWIDETM clock information in the bytes with addresses 7FF9h7FFFh. The clock locations contain the year, month, date, day, hour, minute, and second in 24 hour BCD format. Corrections for 28, 29 (leap year), 30, and 31 day months are made automatically.
2/17
M48T36
Figure 3. Block Diagram
IRQ/FT
WDI
OSCILLATOR AND CLOCK CHAIN 32,768 Hz CRYSTAL POWER BATTERY LOW
8 x 8 BiPORT SRAM ARRAY
8 x 8 ALARM WATCHDOG FLAGS
A0-A14 32,752 x 8 SRAM ARRAY LITHIUM CELL VOLTAGE SENSE AND SWITCHING CIRCUITRY VPFD DQ0-DQ7
E W G
VCC
RST
VSS
AI01626
Table 3. Operating Modes (1)
Mode Deselect Write Read Read Deselect Deselect VSO to VPFD (min) VSO
(2)
VCC
E VIH
G X X VIL VIH X X
W X VIL VIH VIH X X
DQ0-DQ7 High Z DIN DOUT High Z High Z High Z
Power Standby Active Active Active CMOS Standby Battery Back-up Mode
4.5V to 5.5V
VIL VIL VIL X X
Notes: 1. X = VIH or VIL 2. See Table 6 for details.
3/17
M48T36
AC MEASUREMENT CONDITIONS
Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages 5ns 0 to 3V 1.5V
Figure 4. AC Testing Load Circuit
5V
Note that Output Hi-Z is defined as the point where data is no longer driven.
DEVICE UNDER TEST 1k
1.9k
OUT
CL = 100pF or 5pF
CL includes JIG capacitance
AI01030
Table 4. Capacitance (1, 2) (TA = 25 C, f = 1 MHz )
Symbol C IN CIO
(3)
Parameter Input Capacitance Input / Output Capacitance
Test Condition VIN = 0V VOUT = 0V
Min
Max 10 10
Unit pF pF
Notes: 1. Effective capacitance measured with power supply at 5V. 2. Sampled only, not 100% tested. 3. Outputs deselected
Table 5. DC Characteristics (TA = 0 to 70C; VCC = 4.5V to 5.5V)
Symbol ILI ILO
(1) (1)
Parameter Input Leakage Current Output Leakage Current Supply Current Supply Current (Standby) TTL Supply Current (Standby) CMOS Input Low Voltage Input High Voltage Output Low Voltage
Test Condition 0V VIN VCC 0V VOUT VCC Outputs open E = VIH E = VCC - 0.2V
Min
Max 1 5 50 3 3
Unit A A mA mA mA V V V V V
ICC ICC1 ICC2 VIL(2) VIH VOL
-0.3 2.2 IOL = 2.1mA IOL = 10mA IOH = -1mA 2.4
0.8 VCC + 0.3 0.4 0.4
Output Low Voltage (IRQ/FT and (3) RST) Output High Voltage
VOH
Notes: 1. Outputs Deselected. 2. Negative spikes of -1V allowed for up to 10ns once per Cycle. 3. The IRQ/FT and RST pins are Open Drain.
4/17
M48T36
Table 6. Power Down/Up Trip Points DC Characteristics (1) (TA = 0 to 70C)
Symbol VPFD VSO tDR(2) Parameter Power-fail Deselect Voltage (M48T36Y) Battery Back-up Switchover Voltage Expected Data Retention Time 7 Min 4.2 Typ 4.35 3.0 Max 4.5 Unit V V YEARS
Notes: 1. All voltages referenced to VSS. 2. @ 25C
Table 7. Power Down/Up Mode AC Characteristics (TA = 0 to 70C)
Symbol tPD tF
(1) (2)
Parameter E or W at VIH before Power Down VPFD (max) to VPFD (min) VCC Fall Time VPFD (min) to VSO VCC Fall Time VPFD(min) to VPFD (max) VCC Rise Time VSO to VPFD (min) VCC Rise Time VPFD (max) to RST High
Min 0 300 10 10 1 40
Max
Unit s s s s s
tFB
tR tRB tREC
200
ms
Notes: 1. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring until 200 s after VCC passes VPFD (min). 2. VPFD (min) to VSO fall time of less than tFB may cause corruption of RAM data.
Figure 5. Power Down/Up Mode AC Waveforms
VCC VPFD (max) VPFD (min) VSO tF tPD tFB tDR tRB tREC RST tR
INPUTS
RECOGNIZED
DON'T CARE
RECOGNIZED
HIGH-Z OUTPUTS VALID
(PER CONTROL INPUT)
VALID
(PER CONTROL INPUT)
AI01384C
5/17
M48T36
Table 8. Read Mode AC Characteristics (TA = 0 to 70C; VCC = 4.5V to 5.5V)
M48T36Y Symbol Parameter Min tAVAV tAVQV tELQV tGLQV tELQX tGLQX
(1) (1) (1) (2) (2)
-70 Max
Unit
Read Cycle Time Address Valid to Output Valid Chip Enable Low to Output Valid Output Enable Low to Output Valid Chip Enable Low to Output Transition Output Enable Low to Output Transition Chip Enable High to Output Hi-Z Output Enable High to Output Hi-Z Address Transition to Output Transition
70 70 70 35 5 5 25 25 10
ns ns ns ns ns ns ns ns ns
tEHQZ (2) tGHQZ tAXQX
(2) (1)
Notes: 1. CL = 100pF (see Figure 4). 2. CL = 5pF (see Figure 4).
Figure 6. Read Mode AC Waveforms
tAVAV A0-A14 tAVQV tELQV E tELQX tGLQV G tGLQX DQ0-DQ7 VALID
AI00925
VALID tAXQX tEHQZ
tGHQZ
Note: Write Enable (W) = High
6/17
M48T36
Table 9. Write Mode AC Characteristics (TA = 0 to 70C; VCC = 4.5V to 5.5V)
M48T36Y Symbol Parameter Min tAVAV tAVWL tAVEL tWLWH tELEH tWHAX tEHAX tDVWH tDVEH tWHDX tEHDX tWLQZ (1, 2) tAVWH tAVE1H tWHQX
(1, 2)
-70 Max
Unit
Write Cycle Time Address Valid to Write Enable Low Address Valid to Chip Enable Low Write Enable Pulse Width Chip Enable Low to Chip Enable High Write Enable High to Address Transition Chip Enable High to Address Transition Input Valid to Write Enable High Input Valid to Chip Enable High Write Enable High to Input Transition Chip Enable High to Input Transition Write Enable Low to Output Hi-Z Address Valid to Write Enable High Address Valid to Chip Enable High Write Enable High to Output Transition
70 0 0 50 55 0 0 30 30 5 5 25 60 60 5
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Notes: 1. CL = 5pF (see Figure 4). 2. If E goes low simultaneously with W going low, the outputs remain in the high impedance state.
DESCRIPTION (cont'd) Byte 7FF8h is the clock control register. This byte controls user access to the clock information and also stores the clock calibration setting. Byte 7FF7h contains the watchdog timer setting. The watchdog timer detects an out-of-control microprocessor and provides a reset or interrupt to it. Byte 7FF2h-7FF5h are reserved for clock alarm programming. These bytes can be used to set the alarm. This will generate an active low signal on the IRQ/FT pin when the alarm bytes match the date, hours, minutes and seconds of the clock. The eight clock bytes are not the actual clock counters themselves; they are memory locations consisting of BiPORTTM read/write memory cells. The M48T36 includes a clock control circuit which updates the clock bytes with current information once per second. The information can be accessed by the user in the same manner as any other location in the static memory array.
The M48T36 also has its own Power-fail Detect circuit. The control circuitry constantlymonitors the single 5V supply for an out of tolerance condition. When VCC is out of tolerance, the circuit write protects the SRAM, providing a high degree of data security in the midst of unpredictablesystem operation brought on by low VCC. As VCC falls below approximately 3V, the control circuitry connects the battery which maintains data and clock operation until valid power returns. READ MODE The M48T36 is in the Read Mode whenever W (Write Enable) is high and E (Chip Enable) is low. The unique address specified by the 15 Address Inputs defines which one of the 32,768 bytes of data is to be accessed. Valid data will be available at the Data I/O pins within tAVQV (Address Access Time) after the last address input signal is stable, providing that the E and G access times are also satisfied. If the E and G access times are not met,
7/17
M48T36
Figure 7. Write Enable Controlled, Write AC Waveforms
tAVAV A0-A14 VALID tAVWH tAVEL E tWLWH tAVWL W tWLQZ tWHDX DQ0-DQ7 DATA INPUT tDVWH
AI00926
tWHAX
tWHQX
Figure 8. Chip Enable Controlled, Write AC Waveforms
tAVAV A0-A14 VALID tAVEH tAVEL E tAVWL W tEHDX DQ0-DQ7 DATA INPUT tDVEH
AI00927
tELEH
tEHAX
8/17
M48T36
READ MODE (cont'd) valid data will be available after the latter of the Chip Enable Access Time (tELQV) or Output Enable Access Time (tGLQV ). The state of the eight three-state Data I/O signals is controlled by E and G. If the outputs are activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV. If the AddressInputs are changed while E and G remain active, output data will remain valid for tAXQX (Output Data Hold Time) but will go indeterminate until the next Address Access. WRITE MODE The M48T36 is in the Write Mode whenever W and E are low. The start of a write is referencedfrom the latter occurring falling edge of W or E. A write is terminated by the earlier rising edge of W or E. The addresses must be held valid throughoutthe cycle. E or W must returnhigh for a minimumof tEHAX from Chip Enable or tWHAX from Write Enable prior to the initiation of another read or write cycle. Data-in must be valid t DVWH prior to the end of write and remain valid for tWHDX afterward. G should be kept high during write cycles to avoid bus contention; although, if the output bus has been activated by a low on E and G a low on W will disable the outputs tWLQZ after W falls. DATA RETENTION MODE With valid VCC applied, the M48T36 operates as a conventional BYTEWIDE static RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect,write protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs become high impedance, and all inputs are treated as "don't care." Note: A power failure during a write cycle may corrupt data at the currently addressed location, but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the user can be assured the memory will be in a write protected state, provided the VCC fall time is not less than tF. The M48T36 may respond to transient noise spikes on VCC that reach into the deselect window during the time the device is sampling VCC. Therefore, decoupling of the power supply lines is recommended. When VCC drops below VSO, the control circuit switches power to the internal battery which preserves data and powers the clock. The internal button cell will maintain data in the M48T36 for an accumulated period of at least 7 years when VCC is less than VSO. As system power returns and VCC rises above VSO, the battery is disconnected, and the power supply is switched to external VCC. Deselect continues for tREC a f t e r VCC reaches VPFD(max). POWER-ON RESET The M48T36 continuously monitors VCC. When VCC falls to the power fail detect trip point, the RST pulls low (open drain) and remains low on power-up for 40ms to 200ms after VCC passes VPFD. A 1k resistor is recommended in order to control the rise time. The reset pulse remains active with VCC at VSS. PROGRAMMABLE INTERRUPTS The M48T36 has two programmable interrupts: an alarm and a watchdog. When an interrupt condition occurs, the M48T36 sets the appropriate flag bit in the flag register 7FF0h. The interrupt enable bits in 7FF6h and the WDS (Watchdog Steering) bit in 7FF7h allow the interruptto activate the IRQ/FT pin. The interrupt flags and the IRQ/FT output are cleared by a read to the flags register. An interrupt condition reset will not occur unless the addresses are stable at the flag location for at least 15ns while the device is in the read mode as shown in Figure 10. The IRQ/FT pin is an open drain output and requires a pull-up resistor. The pin remains in the high impedance state unless an interrupt occurs or the frequency test mode is enabled. CLOCK OPERATIONS Reading the Clock Updates to the TIMEKEEPER registers should be halted before clock data is read to prevent reading data in transition. Because the BiPORT TIMEKEEPER cells in the RAM array are only data registers, and not the actual clock counters, updating the registers can be halted without disturbing the clock itself.
9/17
M48T36
CLOCK OPERATIONS (cont'd) Updating is halted when a '1' is written to the READ bit, D6 in the Control Register 7FF8h. As long as a '1' remains in that position, updating is halted. After a halt is issued, the registers reflect the count; that is, the day, date, and the time that were current at the moment the halt command was issued. All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an update in progress. Updating is within a second after the bit is reset to a '0'. Setting the Clock Bit D7 of the Control Register 7FF8h is the WRITE bit. Setting the WRITE bit to a '1', like the READ bit, halts updates to the TIMEKEEPER registers. The Table 10. Register Map
Address D7 7FFFh 7FFEh 7FFDh 7FFCh 7FFBh 7FFAh 7FF9h 7FF8h 7FF7h 7FF6h 7FF5h 7FF4h 7FF3h 7FF2h 7FF1h 7FF0h 0 0 0 0 0 ST W WDS AFE RPT4 RPT3 RPT2 RPT1 Y WDF R BMB4 Y Y Y D6 D5 D4 Data D3 D2 Year 10 M. 10 Date 0 0 0 Month Date Day Hours Minutes Seconds Calibration BMB2 Y BMB1 Y BMB0 Y RB1 Y RB0 Y D1 D0 Function/Ran ge BCD Format Year Month Date Day Hour Minutes Seconds Control Watchdog Interrupts Alarm Date Alarm Hours Alarm Minutes Alarm Seconds Y Z Unused Flags 01-31 00-23 00-59 00-59 00-99 01-12 01-31 01-07 00-23 00-59 00-59
user can then load them with the correct day, date, and time data in 24 hour BCD format (see Table 10). Resetting the WRITE bit to a '0' then transfers the values of all time registers 7FF9h-7FFFh to the actual TIMEKEEPER counters and allows normal operation to resume. After the WRITE bit is reset, the next clock update will occur in one second. Stopping and Starting the Oscillator The oscillator may be stopped at any time. If the device is going to spend a significant amount of time on the shelf, the oscillator can be turned off to minimize current drain on the battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the oscillator. The M48T36 is shipped from SGS-THOMSON with the STOP bit set to a '1'.
10 Years 0 0 FT 0 0
10 Hours 10 Minutes 10 Seconds S BMB3 ABE
Al. 10 Date Al. 10 Hours
Alarm Date Alarm Hours Alarm Minutes Alarm Seconds Y Z Y Z Y Z
Alarm 10 Minutes Alarm 10 Seconds Y AF Y Z Y BL
Keys: S = SIGN Bit FT = FREQUENCY TEST Bit R = READ Bit W = WRITE Bit ST = STOP Bit 0 = Must be set to '0' Y = '1' or '0' Z = '0' and are Read only AF = Alarm Flag BL = Battery Low
WDS = Watchdog Steering Bit BMB0-BMB4 = Watchdog Multiplier Bits RB0-RB1 = Watchdog Resolution Bits AFE = Alarm Flag Enable ABE = Alarm in Battery Back-up Mode Enable RPT1-RPT4 = Alarm Repeat Mode Bits WDF = Watchdog Flag
10/17
M48T36
When reset to a '0', the M48T36 oscillator starts within 1 second. Calibrating the Clock The M48T36 is driven by a quartz controlled oscillator with a nominal frequency of 32,768 Hz. The devices are tested not to exceed 35 PPM (parts per million) oscillator frequency error at 25C, which equates to about 1.53 minutes per month. With the calibration bits properly set, the accuracy of each M48T36 improves to better than 4 PPM at 25C. Of course the oscillation rate of any crystal changes with temperature. Most clock chips compensate for crystal frequency and temperature shift error with cumbersome trim capacitors. The M48T36 design, however, employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 128 stage, as shown in Figure 9. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five bit Calibration byte found in the Control Register. Adding counts speeds the clock up, subtracting counts slows the clock down. The Calibration byte occupies the five lower order bits (D4-D0) in the Control Register 7FF8h. These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a Sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 PPM of adjustment per calibration step in the calibration register. Assuming that the oscillator is in fact running at exactly 32,768 Hz, each of the 31 increments in the Calibration byte would represent +10.7 or - 5.35 seconds per month which corresponds to a total range of +5.5 or - 2.75 minutes per month. Two methods are available for ascertaining how much calibration a given M48T36 may require. The first involves simply setting the clock, letting it run for a month and comparing it to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows the designer to give the end user the ability to calibrate his clock as his environment may require, even after the final product is packaged in a non-user serviceable enclosure. All the designerhas to do is provide a simple utility that accesses the Calibration byte. The utility could even be menu driven and made foolproof. The second approach is better suited to a manufacturing environment, and involves the use of the IRQ/FT pin. The pin will toggle at 512Hz when the Stop bit (D7 of 7FF9h) is '0', the FT bit (D6 of 7FFCh) is '1', the AFE bit (D7 of 7FF6h) is '0', and the Watchdog Steering bit (D7 of 7FF7h) is '1' or the Watchdog Register is reset (7FF7h = 0). Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at the test temperature. For example, a reading of 512.01024 Hz would indicate a +20 PPM oscillator frequency error, requiring a -10(001010) to be loaded into the Calibration Byte for correction. Note that setting or changing the Calibration Byte does not affect the Frequency test output frequency.
Figure 9. Clock Calibration
NORMAL
POSITIVE CALIBRATION
NEGATIVE CALIBRATION
AI00594
11/17
M48T36
CLOCK OPERATIONS (cont'd) The IRQ/FT pin is an open drain output which requires a pull-up resistor for proper operation. A 500-10k resistor is recommended in order to control the rise time. The FT bit is cleared on power-up. SETTING ALARM CLOCK Registers 7FF5h-7FF2h contain the alarm settings. The alarm can be configured to go off at a prescribed time on a specific day of the month or repeat every day, hour, minute, or second. It can also be programmed to go off while the M48T36 is in the battery back-up mode of operation to serve as a system wake-up call. RPT1-RPT4 put the alarm in the repeat mode of operation. Table 11 shows the possible configurations. Codes not listed in the table default to the once per second mode to quickly alert the user of an incorrect alarm setting. When the clock information matches the alarm clock settings based on the match criteria defined by RPT1-RPT4, AF (Alarm Flag) is set. If AFE (Alarm Flag Enable) is also set, the alarm condition activates the IRQ/FT pin. The alarm flag and the IRQ/FT output are cleared by a read to the Flags register as shown in Figure 10. The IRQ/FT pin can also be activated in the battery back-up mode. The IRQ/FT will go low if an alarm occurs and both ABE (Alarm in Battery Back-up Mode Enable) and AFE are set. The ABE and AFE bits are reset during power-up, therefore an alarm generated during power-up will only set AF. The user can read the Flag Register at system boot-up to determine if an alarm was generated while the M48T36 was in the deselect mode during powerup. Figure 11 illustrates the back-up mode alarm timing. Table 11. Alarm Repeat Mode
RPT4 1 1 1 1 0 RPT3 1 1 1 0 0 RPT2 1 1 0 0 0 RPT1 1 0 0 0 0 Alarm Activated Once per Second Once per Minute Once per Hour Once per Day Once per Month
Figure 10. Interrupt Reset Waveforms
15ns Min A0-A14 ADDRESS 1FF0h
ACTIVE FLAG BIT
IRQ/FT HIGH-Z
AI01627
12/17
M48T36
WATCHDOG TIMER The watchdog timer can be used to detect an out-of-control microprocessor. The user programs the watchdog timer by setting the desired amount of time-out into the eight bit Watchdog Register, address 7FF7h. The five bits (BMB4-BMB0) store a binary multiplier and the two lower order bits (RB1-RB0) select the resolution, where 00=1/16 second, 01=1/4 second, 10=1 second, and 11=4 seconds. The amount of time-out is then determined to be the multiplication of the five bit multiplier value with the resolution. (For example: writing 00001110 in the Watchdog Register = 3 x 1 or 3 seconds). If the processor does not reset the timer within the specified period, the M48T36 sets the WDF (Watchdog Flag) and generates a watchdog interrupt or a microprocessor reset. The most significant bit of the Watchdog Register is the Watchdog Steering Bit. When set to a '0', the watchdog will activate the IRQ/FT pin when timedout. When WDS is set to a '1', the watchdog will output a negative pulse on the RST pin for a duration of 40ms to 200ms. The Watchdog register and the FT bit will reset to a '0' at the end of a watchdog time-out when the WDS bit is set to a '1'. The watchdog timer resets when the microprocessor performs a read of the Watchdog Register. The time-out period then starts over. The watchdog timer is disabled by writing a value of 00000000 to the eight bits in the Watchdog Register. The watchdog function is automatically disabled upon powerup and the Watchdog Register is cleared. If the watchdog function is set to outputto the IRQ/FT pin and the frequency test function is activated, the watchdog function prevails and the frequency test function is denied. The WDI pin contains a pull-up resistor which is greater than 100k, and therefore can be left unconnected if not used. BATTERY LOW WARNING The M48T36 checks it's battery voltage on powerup. The BL (Battery Low) bit D4 of 7FF0h will be set on power-up if the battery voltage is less than 2.5V (typical). POWER-ON DEFAULTS Upon application of power to the device, the following register bits are set to a '0' state: WDS = 0; BMB0-BMB4 = 0; RB0-RB1 = 0; AFE = 0; ABE = 0.
Figure 11. Back-up Mode Alarm Waveforms
VCC VPFD (max) VPFD (min)
AFE
AF
IRQ/FT HIGH-Z HIGH-Z
AI01389B
13/17
M48T36
ORDERING INFORMATION SCHEME
Example:
M48T36Y
-70
MH
1
Supply Voltage and Write Protect Voltage 36Y VCC = 4.5V to 5.5V VPFD = 4.2V to 4.5V -70
Speed 70ns MH
Package SOH44
Temp. Range 1 0 to 70 C
The SO and battery packages are shipped separately in plastic anti-static tubes. The SO package is also available to ship in Tape & Reel form. For the 44 lead SO, the battery package (i.e. SNAPHAT) part number is "M4T44-BR12SH1".
For a list of available options (Supply Voltage, Speed, Package, etc...) refer to the current Memory Shortform catalogue. For further information on any aspect of this device, please contact the SGS-THOMSON Sales Office nearest to you.
14/17
M48T36
SOH44 - 44 lead Plastic Small Outline, battery SNAPHAT
Symb Typ A A1 A2 B C D E e eB H L N CP
SOH44
mm Min Max 3.05 0.05 2.34 0.36 0.15 - - 8.23 1.27 - 3.20 11.51 0.41 0 44 0.10 0.36 2.69 0.51 0.32 - 8.89 - 3.61 12.70 1.27 8 0.050 - Typ
inches Min Max 0.120 0.002 0.092 0.014 0.006 - 0.324 - 0.126 0.453 0.016 0 44 0.004 0.014 0.106 0.020 0.012 - 0.350 - 0.142 0.500 0.050 8
A2 B e
A C eB CP
D
N
E
H A1 L
1 SOH
Drawing is not to scale
15/17
M48T36
SH44 - SNAPHAT Housing for 44 lead Plastic Small Outline
Symb Typ A A1 A2 A3 B D E eA eB L
SH44
mm Min Max 9.78 6.73 6.48 7.24 6.99 0.38 0.46 - - 14.22 - - 3.20 2.03 0.56 - 14.99 - 3.61 2.29 - - Typ
inches Min Max 0.385 0.265 0.255 0.285 0.275 0.015 0.018 - 0.560 - 0.126 0.080 0.022 - 0.590 - 0.142 0.090
A1
A2 A A3
eA D
B eB
L
E
SH
Drawing is not to scale
16/17
M48T36
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. (c) 1995 SGS-THOMSON Microelectronics - All Rights Reserved TM TIMEKEEPER, SNAPHAT, BYTEWIDE and BiPORT are trademarks of SGS-THOMSON Microelectronics SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.
17/17

▲Up To Search▲

Price & Availability of M48T36

	To Download M48T36 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .